.500″ 1/2″ 2 Flute Extra Long Length Carbide Ball END Mill 1/2″ x 1/2″ x 3″ x 6″
- 1/2″2 flute single end extra long carbide ball end mill6″ overall length3″ flute lengthuncoatedmade in usa175-2500.
YG-1 E5062 Carbide Ball Nose End Mill, Extra Long Reach, Uncoated (Bright) Finish, 30 Deg Helix, 4 Flutes, 3″ Overall Length, 0.125″ Cutting Diameter, 0.125″ Shank Diameter
- Extra-long-length end mills have longer cutting edges and can make deeper cuts than long-length end mills. Four flutes produce a better finish than fewer flutes. Suitable for machining on hardened and high-alloy steel, steel casting, chill casting, malleable cast iron, chromium-nickel steel, brass, copper, aluminum with a high percentage of silicon, and abrasive plastic. Carbide can run at higher speeds than high-speed or cobalt steel, resisting wear and high cutting temperatures. Ball nose end mills (also called ball end) create contoured surfaces.
.375″ 3/8″ 4 Flute Extra Long Length Carbide Ball END Mill 3/8″ x 3/8″ x 3″ x 6″
- 3/8″4 fluteextra long lengthcarbide ball end mill6″ overall length3″ flute lengthuncoatedmade in usa175-4336.
SpeTool 14412 Ball Nose Carbide End Mill CNC Cutter Router Bits Double Flute Spiral Milling Tool 3/8 inch Shank with 3 inch OVL
- Round top with 2-flute, material hrc55 carbide with tialn coated. Solid carbide ball nose router bit with 3/8inch shank and 3/8inch cutting diameter, 1-1/8 inch cutting length, 3 inch for total length. End mill bits are suitable for side milling, end milling, finish machining, etc. For cnc,engraving machinecarbon steel, mould steel, inconel, stainless steel, titanium alloy etc. The route bit suit for cnc router and makita, bosch, and any brand plunge router with 1/4″ collet.
YG-1 E5014 Carbide Ball Nose End Mill, Long Reach, Uncoated (Bright) Finish, 30 Deg Helix, 2 Flutes, 2.25″ Overall Length, 0.125″ Cutting Diameter, 0.125″ Shank Diameter
- Carbide can run at higher speeds than high-speed or cobalt steel, resisting wear and high cutting temperatures. Two flutes offer better chip-carrying capacity than end mills with more flutes, enhancing the tool’s ability to remove material. Ball nose end mills (also called ball end) create contoured surfaces. Long-length end mills have longer cutting edges and can make deeper cuts than standard-length end mills. Suitable for machining on hardened and high-alloy steel, steel casting, chill casting, malleable cast iron, chromium-nickel steel, brass, copper, aluminum with a high percentage of silicon, and abrasive plastic.
ACCUPRO Carbide Ball End Mill 0.040″ 2FL AlTiN 64536394
- Shank 1/8″. Overall length 1-1/2″. Finish tialn. Length of cut 0120″. Material carbide.
Niagara Cutter N47942 Carbide Ball Nose End Mill, Metric, AlTiN Finish, Roughing and Finishing Cut, 30 Degree Helix, 4 Flutes, 51mm Overall Length, 6mm Cutting Diameter, 6.000mm Shank Diameter
- Four flutes produce a better finish than fewer flutes. Ball nose end mills (also called ball end) create contoured surfaces. Aluminum titanium nitride (altin) coating lubricates the end mill for high-temperature stability and abrasion resistance, offering better heat resistance than tin, tialn, and ticn coatings. Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling. Carbide can run at higher speeds than high-speed steel, resisting abrasion and high cutting temperatures.
JERRAY Made Solid Carbide Ball Nose End Mill, HRC55 with AlTiN Coated, 4 Flutes, 1/4″ Shank, 1/2″ Length of Cut, 2″ Overall Length, 1/4″ Diameter,1/8″ Radius
- Typeballnose end mills / brand name jerray tools. Material tungsten carbide / quantity 1 piece / package hard plastic box. Helix 35 / number of flute 4f / coating tiain. Flutes length1/2″ / overall length 2″ / work material hardness hrc55. Cutting radius 1/8″ shank diameter1/4″ / cutting diam1/4″.
YG-1 52558TC Carbide Ball Nose End Mill, 2 Flute, Extra Long Length, TiCN Finish, 3″ Length, 1/8″
- Leveraging a competitive spirit and vertical integration allows us to provide the highest quality at the best price. A global leader in cutting tools, yg-1 has been providing high performance mills, drills, taps and rotary tools for over 20 years. This is why we say if it’s not yg-1, it’s not perfect.
Melin Tool CCMG-EB Carbide Ball Nose End Mill, AlTiN Monolayer Finish, 30 Deg Helix, 4 Flutes, 6″ Overall Length, 0.6250″ Cutting Diameter, 0.625″ Shank Diameter
- Designed to cut materials ranging from nickel base alloy, stainless, tough alloys, abrasive and nonferrous. Use for radius and contouring part surfaces. Solid carbide tools offer long tool life and faster cutting speeds than other substrates, but are more brittle and must be used with rigid toolholding systems. Round shanks allow use with a wide variety of toolholding systems. Aluminum titanium nitride is similar to tialn but with a higher aluminum content for improved hardness and smoothness.
Kodiak Cutting Tools KCT132856 USA Made Ball Nose Solid Carbide End Mill, 4 Flute, 1/8″ Shank, 1/2″ Length of Cut, 1-1/2″ Overall Length, 1/8″ Size
- 0004″. 1/8 inch diameter ball nose solid carbide end mill, single end 1/8″ shank 1/2″ length of cut 1-1/2″ overall length 4 flute carbide, single end diameter tolerance +. 000″/-. 002″shank diameter tolerance -. 0001″/-.
Kodiak Cutting Tools LD-B4PZ-OVEL USA Made Micrograin Carbide Ball Nose End Mill Set, 2 Flute, 1/8″ to 1/2″ (Pack of 6)
- Contains 1 piece of the following diameters 1/8, 3/16, 1/4, 5/16, 3/8 and 1/2. 2 flute ball nose end mills are center cutting and made from premium sub-micrograin carbide. Stub length end mills for extra rigidity. Contains kodiak cutting tools brand premium quality usa made ball nose solid carbide end mills. Fitted wood block stand included and each size comes in a marked plastic tube.
SpeTool 14411 Ball Nose Carbide End Mill CNC Cutter Router Bits Double Flutes Spiral Milling Tool 1/4 inch Shank with 3 inch over Length
- Solid carbide ball nose router bit with 1/4inch shank and 1/4inch cutting diameter, 1-1/8 inch cutting length, 3 inch for total length. The route bit suit for cnc router and makita, bosch, and any brand plunge router with 1/4″ collet. Round top with 2-flute, material hrc55 carbide with tialn coated. For cnc,engraving machinecarbon steel, mould steel, inconel, stainless steel, titanium alloy etc. End mill bits are suitable for side milling, end milling, finish machining, etc.
Niagara Cutter N85906 Carbide Ball Nose End Mill, Inch, Weldon Shank, TiAlN Finish, Roughing and Finishing Cut, 30 Degree Helix, 4 Flutes, 2″ Overall Length, 0.188″ Cutting Diameter, 0.188″ Shank Diameter
- Ball nose end mills (also called ball end) create contoured surfaces. Nc tolerance end mills have a plus-tolerance cutting diameter to match those of high-speed steel end mills, allowing an upgrade from high-speed steel to carbide without changing diameter. Titanium aluminum nitride (tialn) coating lubricates the end mill for high-temperature stability and abrasion resistance at high cutting speeds, offering better heat resistance than tin and ticn coatings. Carbide can run at higher speeds than high-speed steel, resisting abrasion and high cutting temperatures. Four flutes produce a better finish than fewer flutes.
CNC Carving 2.12 Deg 2 Flutes Tapered Angle Ball Tip Radius=2.0mm X 1/4″ Shank Tungsten Solid Carbide HRC55 with TiAIN Coated
- Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling. Aluminum titanium nitride (altin) coating lubricates the end mill for high-temperature stability and abrasion resistance, offering better heat resistance than tin, tialn, and ticn coatings. Ball nose end mills (also called ball end) create contoured surfaces. Carbide can run at higher speeds than high-speed steel, resisting abrasion and high cutting temperatures. Four flutes produce a better finish than fewer flutes.
Milling Cutter – 16pcs Wooden Bead Drill Bit Carbide Ball Blade Molding Tool Router Woodworking Milling Cutter 25mm – Injured Minute Moment Routine Stung
- Bead cutter drill bit molding carbide blade router knife edge tool. Milling tool spmt120408 bit carbide woodwork cutter unfinish wood bead router. This item can be searched by below relevant keywords milling cutter scodak. Milling cutter knife impacte drill router bit printing for wood. Router bit beading cutter bead wood blade knife ball moulding tool.
Kodiak Cutting Tools KCT146089 USA Made Micro Carbide Ball Nose End Mill, 2 Flute, 1/8″ Shank, 0.108″ Diameter
- 324″ length of cut 1-1/2″ overall length 2 flute carbide, micro. 108 inch diameter solid carbide end mill, micro 0. 125″ shank 0.
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
