Simpson Strong Tie CBSQ66-SDS2HDG 1 1 1 6-Inch by 6-Inch Column Base with SDS Screws Hot Dipped Galvanized
- Post and column bases secure the bottom of posts or columns to concrete and are perfect for decks or patio covers. Models are available for attaching to existing hardened concrete, wet concrete, as well as wood. The cbsq series provides a connection between a post (or column) for decks, patio covers and other top-supported structures. .
Simpson Strong Tie SDS25300-R25 1/4″ x 3″ Hex Head Wood Screw 25 per Package
- 1/4″ x 3″ sds screw, 2″ thread length. Double-barrier coating finish provides corrosion resistance superior to hot-dip galvanization. 25 per pack. 3/8″ hex washer head stamped w/no-equal sign & fastener length for easy identification after install. 4cut tip reduces install torque & makes driving easier with no predrilling & minimal wood splitting.
Simpson Strong Tie SDWH19600DB-RC12 0.195″ x 6″ Stong-Drive Structural Wood Screws with Large Hex-Washer Head – 12 per Package
- Installs best with a low-speed 1/2″ drill motor with a 5/16″ hex driver (bit included in each package). Patented 4cut point ensures fast starts, reduced installation torque and eliminates the need for pre-drilling in most applications. Large head provides maximum bearing area. Double-barrier coating provides corrosion resistance equivalent to hot-dip galvanization, making it suitable for many exterior and preservative-treated wood applications. Knurled shank section above the threads makes driving easier. Under-head nibs offer greater installer control when seating the head. Large hex-washer head provides excellent bearing area for a secure connection. Hex drive reduces cam-outs for easier driving. Bold thread design provides superior holding power and cinches fastened members together for consistent installation. Strong-drive® sdwh structural wood screws, large hex-washer head, for structural wood-to-wood connections, designed to provide an easy-to-install, high-strength alternative to through-bolting and traditional lag screws.
Simpson Strong Tie ECCQ5-6SDS2.5 5-1/8″ Beam 6x Post End Column Cap w/SDS Screws
- 9. . 5 5 x 6 end column cap with screws. This product is a eccq5-6sds2. 62 models assume a minimum 3 1/2″ wide post. Eccq uses 14-sds screws into the beam and 14-sds screws into the post. 4. Values in the tables reflect installation into the wide face. Weld by designer. Column sides are assumed to lie in the same vertical plane as the beam sides. Uplift loads do not apply to splice conditions. See post capacities for common post allowable loads. Steel column width shall not be less than beam width. 8., General notes install simpson strong-tie sds 1/4″x 2-1/2″ wood screws, which are provided with the column cap. Structural composite lumber columns have sides that show either the wide face or the edges of the lumber strands/veneers. Ccq4. (Lag screws will not achieve the same load. 2. 6. ) Additional general notes 1. Beam depth must be a minimum 7″. 7. Ccoq welded to steel column will achieve same load as ccq. Uplift loads have been increased for wind or earthquake with no further increase allowed reduce where other loads govern. 10. Down loads may not be increased for short-term loading and shall not exceed the post capacity. 3. See technical bulletin t-sclcolumn for values on the narrow face (edge). 5. Spliced conditions must be detailed by the designer to transfer tension loads between spliced members by means other than the column cap. For 5 1/4″ engineered lumber, use ccq 6x or eccq 6x models.
Simpson Strong Tie HUCQ1.81/9-SDS 1-13/16-Inch by 9-Inch Heavy Duty Joist Hanger Concealed/Reverse Flange with SDS Screws
- Simpson strong-tie connectors make projects easier to build while making them stronger and safer. . They are engineered and tested to perform and are manufactured to the highest quality standards. Whether working on a home project or building a structure to comply with building codes, go with the choice of engineers and contractors, go with genuine simpson strong-tie connectors.
6 Pack Simpson Strong Tie SDS25412-R10 1/4″ x 4-1/2″ Hex Head Wood Screw 10 per Package
- 1/4″ x 4-1/2″ sds screw, 2-3/4″ thread length. Double-barrier coating finish provides corrosion resistance superior to hot-dip galvanization. 4cut tip reduces install torque & makes driving easier with no predrilling & minimal wood splitting. 3/8″ hex washer head stamped w/no-equal sign & fastener length for easy identification after install. 10 per pack.
Simpson Strong Tie HDU2-SDS2.5 14-Gauge 8-11/16 in. Predeflected Holdown with SDS Screws
- No stud bolts to countersink at openings. Sds screws are supplied with the holdowns to ensure proper fasteners are used. Uses sds screws which install easily, reduces fastener slip, and provides a greater net section area of the post compared to bolts. Height 8-11/16 in. Pre-deflected body virtually eliminates deflection due to material stretch.
10 Pack Simpson Strong Tie UFP10-SDS3 6-3/4″ x 10″ Universal Foundation Plate w/SDS Screws
- The ufp may be used in place of the fa, hfa and fap connectors. The ufp is also designed to perform when the mudsill is offset from the foundation up to 2 1/2″ or extended beyond the foundation up to 1/2″. . The ufp provides a retrofit method to anchor the mudsill to the side of the foundation in applications where minimum vertical clearance exists.
Simpson Strong Tie CJT3L 4×8 Concealed Joist Tie with 3 Long Pins & SDS Screws
- Includes (3) 4-3/4″ chamfered steel pins and (6) sds screws. 5-9/16″ (h1) x 4-7/16″ (h2). 12 gauge material. Zinc galvanized finish containing 090oz of zinc per square foot of surface area (total both sides). For minimum joist size 4×8 douglas fir, 3-1/8″x7-1/2″ glulam beam or 3-1/2″ x 9-1/2″ psl.
Simpson Structural Screws SDS25212-R25 1/4-Inch by 2-1/2-Inch with 1-1/2-Inch threaded Structural Wood Screw, 25-Pack
- 3/8-inch hex head. Head is stamped with simpson strong tie stamp and fastener length for easy identification. Meets icc-es esr-2236 codes. Patented 4-cut point and type 17 point enables easy driving without pre-drilling and minimalm splitting. Low speed 1/2-inch drill with 3/8-inch hex driver recommended for installation.
Simpson Strong Tie DSC5L-SDS3 Drag Strut Connector Left Hand with SDS Screws
- Simpson strong-tie connectors make projects easier to build while making them stronger and safer. Whether working on a home project or building a structure to comply with building codes, go with the choice of engineers and contractors, go with genuine simpson strong-tie connectors. The dsc drag-strut connector transfers the diaphragm shear forces from the girder truss or beam to the shear walls. They are engineered and tested to perform and are manufactured to the highest quality standards. The new dsc5 has been designed to optimize fastener location, resulting in a connector that outperforms the dsc4 with fewer fasteners.
Simpson Structural Screws SDS25412-R10 1/4-Inch by 4-1/2-Inch with 2-3/4-Inch threaded Structural Wood Screw, 10-Pack
- Low speed 1/2-inch drill with 3/8-inch hex driver recommended for installation. Head is stamped with simpson strong tie stamp and fastener length for easy identification. Meets icc-es esr-2236 codes. 3/8-inch hex head. Patented 4-cut point and type 17 point enables easy driving without pre-drilling and minimalm splitting.
Simpson Strong Tie HSS2-SDS1.5 Stud Shoe with Screws
- 5 stud shoe is designed to reinforce 2 x studs notched in construction. The hss2-sds1. It has easy-to-use flanges that can be bent up to 90 degrees during installation and then bent back for fastening. Provides tension load capacity as well as increased compression loads.
Simpson Strong Tie HUCQ410-SDS 4×10 Heavy Duty Joist Hanger Concealed/Reverse Flange w/SDS Screws
- Hucq, features concealed flanges so it can be installed close to the end of the supporting beam. To achieve maximum loads, fill both round and triangle holes with common nails. (Do not bend or remove tabs). Most models have triangle and round holes. All hangers in this series have double-shear nailing. It also allows the use of fewer nails, faster installation, and the use of common nails for all connections. They install with sds screws (supplied with the hanger) for high capacity and ease of installation. This patented innovation distributes the load through two points on each joist nail for greater strength.
Simpson Strong Tie ECCQ64SDS2.5 6x Beam 4x Post End Column Cap w/SDS Screws
- This design uses sds screws to provide faster installation and provides a greater net section area of the column compared to bolts. The sds screws provide for a lower profile compared to standard through bolts. Column caps provide a high capacity connection for column-beam combinations.
Simpson Strong Tie DTT2Z-SDS2.5 ZMAX Galvanized 14-Gauge 2x Deck Tension Tie with SDS Screws
- Suitable for lighter-duty hold own applications on single or double 2x posts. Zmax galvanization offers extra corrosion resistance for exterior and treated-wood applications. Installs easily with strong-drive sds screws (included). Install with sds 1/4 in x 2-1/2 in screws (included). Made from 14 gauge steel.
Simpson Strong-Tie SDS25800-R10 1/4″ X 8″ SDS Screw Retail Pack 10Ct
- Sds screws provide for a lower profile compared to standard through bolts. Made from 7-gauge steel. Includes 30, 1/4-inch x 2-1/2-inch sds screws 16 for beam and 14 for post. 4x beam width.
Simpson Strong Tie CBSQ44-SDS2 12-Gauge Standoff Column Base with SDS Screws
- Uses simpsons sods screws which allow for fast installation. Provides a 1 in standoff between post and concrete that meets code requirements. Base plate provides 1″. Uses strong-drive screws, which allow for fast installation, reduced reveal and high capacity. The standoff base reduces the potential for decay at post and column ends. Shipped with base plate assembled. Embeds in wet concrete at time of pour. Reduced reveal & high capacity.
6 Pack Simpson Strong Tie HDU8-SDS2.5 16-5/8″ Predeflected Hold Down w/SDS Screws
- 3″w x 16-5/8″h x 3-1/2″b. Pre-deflected body virtually eliminates deflection due to material stretch. 7/8″ anchor bolt diameter. Sds 1/4″x2 1/2″ screws are supplied with the holdowns. Zinc galvanized finish containing 090oz of zinc per square foot of surface area (total both sides).
Simpson Structural Screws SDS25300-R25 1/4-Inch by 3-Inch with 2-Inch threaded Structural Wood Screw, 25-Pack
- Head is stamped with simpson strong tie stamp and fastener length for easy identification. Meets icc-es esr-2236 codes. 3/8-inch hex head. Low speed 1/2-inch drill with 3/8-inch hex driver recommended for installation. Patented 4-cut point and type 17 point enables easy driving without pre-drilling and minimalm splitting.
Simpson Strong Tie DSC5R-SDS3 Drag Strut Connector Right Hand with SDS Screws
- The new dsc5 has been designed to optimize fastener location, resulting in a connector that outperforms the dsc4 with fewer fasteners. Whether working on a home project or building a structure to comply with building codes, go with the choice of engineers and contractors, go with genuine simpson strong-tie connectors. Simpson strong-tie connectors make projects easier to build while making them stronger and safer. They are engineered and tested to perform and are manufactured to the highest quality standards. The dsc drag-strut connector transfers the diaphragm shear forces from the girder truss or beam to the shear walls.
Simpson Structural Screws SDS25312MB 1/4-Inch by 3-1/2-Inch with 2-1/4-Inch threaded Washer-Head Screw, 125-Pack
- 3/8-inch hex head. Low speed 1/2-inch drill with 3/8-inch hex driver recommended for installation. Head is stamped with simpson strong tie stamp and fastener length for easy identification. Patented 4-cut point and type 17 point enables easy driving without pre-drilling and minimalm splitting. Meets icc-es esr-2236 codes.
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
