Aluminum Jumbo / Cole Jaws for Hurricane HTC100 Woodturning 4 Jaw Wood Lathe Chuck
- Will hold drill bits up to 1/2-inch in diameter. Drill chuck mounts in the 2 mt. Can be used in either the headstock or tailstock. Removed easily with a knock-out bar. Tightens by hand without the need for a chuck key.
Hurricane Turning Tools, Spigot Jaws for HTC100 Woodturning 4 Jaw Wood Lathe Chuck
- This listing is for a set of spigot jaws, which are used on the hurricane htc100 4 jaw woodturning scroll chuck. Spigot jaws can be used in expansion mode for internal holding within a straight wall. These jaws are only compatible with the htc100. Normally, these are used holding small items like a box or lid. The outside jaws are serrated. In compression mode, they can be used for holding small work. They are very useful for holding inside a candlestick.
Hurricane Turning Tools, Large Serrated Jaws for HTC100 Woodturning 4 Jaw Wood Lathe Chuck
- Some turners use the serrated jaws instead of dovetail jaws in compression mode for gripping a tenon or expansion mode for internal holding within a recess. They can be used for this but they are not as strong as dovetail jaws. . They differ from dovetail jaws in that they are not tapered and have tiny gripping “serrations”. This listing is for a set of large serrated jaws, which are used on the hurricane htc100 4 jaw woodturning scroll chuck. Serrated jaws are used for gripping end grain cylinders.
Hurricane Turning Tools, Extended Dovetail Jaws for HTC100 Woodturning 4 Jaw Wood Lathe Chuck
- You can also use them in compression mode to hold small object down to these jaws are only compatible with the htc100. They are used in expansion mode for internal holding within a dovetail recess. The dovetail is set away from the flat jaw surface by about 1 inch. This gives you better access to the bottom of the bowl for easier tool work while your bowl is on the lathe. This listing is for a set of extended dovetail jaws, sometimes called spindle nose jaws, which are used on the hurricane htc100 4 jaw woodturning scroll chuck. .
Hurricane Turning Tools, Jumbo/Cole Jaws for HTC100 Woodturning 4 Jaw Wood Lathe Chuck
- The buttons open to about 12 inches. . These jaws are only compatible with the htc100. The jaw set comes with 8 buttons which can be placed in the various hole locations to accommodate a variety of bowl sizes. This listing is for a set of jumbo / cole jaws, which are used on the hurricane htc100 4 jaw woodturning scroll chuck. These jaws are used for gripping the top of a bowl in compression or expansion mode, allowing you to finish the bottom of the bowl.
PSI CMG3C Mini Grip 4 Jaw Wood Lathe Chuck System
- Basic straight jaws for 1-inch stock, square or round. Flat jaws to handle bowls up to 5-inch diameter are available (#cjawfj1). Adapts to both 3/4-inch-by-16 tpi and 1-by-8 tpi spindles, and contains 2 open/close levers. Bonus jaws to hold dowels 1-1/2-to-2-3/8-inch to grip internally 2-to-3-inch. Stepped jaws for small dowels 3/8-to-1-1/4-inch to grip internally 1-to-2-1/2-inch.
Sherline 1043 – 3-Jaw Self-centering Wood Lathe Chuck
- The hole through the chuck is. 0001″. . Because this chuck was initially designed for machine-lathe work, its accuracy far exceeds what is necessary for general wood turning. Rotating the knurled ring closes all three jaws simultaneously to quickly grip round or hexagonal stock. It has a clamping range of 3/32″ (2 mm) up to 1-3/16″ (30 mm) diameter with the jaws in the normal position. Grinding is done to within. This assure maximum accuracy. If you have sent in an old chuck for jaw replacement or are replacing an old, worn chuck, you will notice that the new one is initially harder to turn than your worn one. Jaw tightness on scrolling chucks. With the jaws in the reversed position, work up to 2-1/4″ (56 mm) can be gripped. As chucks wear, they become looser and easier to turn. 1″ diameterthis chuck is identical to our p/n 1040 self-centering chuck except that it has a 1″-8 tpi thread that accommodates most wood-working lathes. 687″ (17 mm). Tommy bars (provided) are used in the holes in the side to tighten and loosen the chuck for more leverage. Sherline technicians custom grind each jaw to fit its own slot with as little play as possible. Sherline 1043, 3-jaw self-centering wood lathe chuck 3.
Aluminum Jumbo / Cole Jaws for Hurricane HTC125 Woodturning 4 Jaw Wood Lathe Chuck
- They must be used at slow speeds (500 rpm or slower), with the tailstock live center in place and never in reverse rotation. If you have a bigger bowl you would like to finish, we recommend making your own “doughnut chuck” which you can easily find on google or youtube. The jaw set comes with 8 buttons which can be placed in the various hole locations to accommodate a variety of bowl sizes. Jumbo or “cole” jaws are used for gripping the top of a bowl in compression or expansion mode, allowing you to finish the bottom of the bowl. Measurements plate diameter = 9 3/4″ closed, 12″ fully open bowl size will be less than the plate diameter because of the buttons. We have kept the diameter small (~10 inches) for safety (sorry). Cole jaws (regardless of brand) are designed for light finishing cuts on the foot of a bowl or platter. Our new design is made from lightweight cast aluminum for less inertia as compared to the original steel design. These jaws are only compatible with the htc125. They are designed for heavy cuts, as the buttons do not provide enough holding power to keep the piece securely in place.
PSI Woodworking LCM18X 3 Jaw Micro Wood Lathe Chuck
- The smaller diameter offers a safety feature keeping your knuckles away from the jaws when working close to the chuck. Holds a workpiece from 3/4″ to 2-1/2″ inside diameter, and a workpiece from zero to 1-1/4″ outside diameter. Uses small levers to open and tighten the three jaws. The provided step jaws reverse for extra versatility when securing the work piece from the outside, or inside. Pre cut with a 1″ x 8 tpi standard thread mount, and includes an adapter for 3/4″ x 16 tpi spindles. . Weighs only 1. This self centering, 3 jaw micro chuck is ideal for holding small projects from the inside or outside. 2 pounds.
Hurricane Turning Tools, Standard Dovetail Jaws for HTC100 Woodturning 4 Jaw Wood Lathe Chuck
- They are typically used in compression mode for holding a tenon or “foot” on the bottom of a bowl or platter. These jaws are normally included in the basic chuck kit, but you might need an extra set, or purchased a chuck as “body only” these jaws are only compatible with the htc100. This listing is for a set of standard dovetail jaws, which are used on the hurricane htc100 4 jaw woodturning scroll chuck. Standard dovetail jaws are the most common jaw type used in woodturning. They can also be used in expansion mode for holding inside a dovetail recess. Measurements compression 1 3/4″, 3″ expansion 2 1/4″, 3 1/2″.
Hurricane Turning Tools, Extended Dovetail Jaws for HTC125 Woodturning 4 Jaw Wood Lathe Chuck
- This listing is for a set of extended dovetail jaws, sometimes called spindle nose jaws, which are used on the hurricane htc125 4 jaw woodturning scroll chuck. You can also use them in compression mode to hold small object down to these jaws are only compatible with the htc125. They are used in expansion mode for internal holding within a dovetail recess. The dovetail is set away from the flat jaw surface by about 1 inch. This gives you better access to the bottom of the bowl for easier tool work while your bowl is on the lathe.
Hurricane Turning Tools, Spigot Jaws for HTC125 Woodturning 4 Jaw Wood Lathe Chuck
- The outside jaws are serrated. This listing is for a set of spigot jaws, which are used on the hurricane htc125 4 jaw woodturning scroll chuck. These jaws are only compatible with the htc125. Spigot jaws can be used in expansion mode for internal holding within a straight wall. Normally, these are used holding small items like a box or lid. In compression mode, they can be used for holding small work. They are very useful for holding inside a candlestick.
PSI CSC2000C Barracuda Wood Lathe Chuck System
- Includes pin jaws which hold inside holes 1″, 2-1/2″, and a screw chuck. Includes #3 round jaws, external grip 3-1/16″, 4-1/2″. Includes #2 round jaws, for dowels1-1/2″ to 2-7/8″, holes 2″ to 3-1/2″. Includes four(4) self-centering jaw sets to hold round and square stock for turning, pre-threaded for 1″ x 8 tpi, and has an adapter for 3/4″ x 16 tpi spindles. Includes #1 step jaws- for dowels 1/32″ to 1-1/2″, holes 11/16″to 3-1/8″.
PSI CMG3C Mini Grip 4 Jaw Wood Lathe Chuck System by PSI Woodworking
- Psi cmg3c mini grip 4 jaw wood lathe chuck system. Also includes 8 extra long mounting screws for double jaws use (see description). Kit includes 6040 12″ cole jaws, 6039 12-15″ cole jaw adaptors, and 6030 buffer acc kit. For large bowl turning (requires 16″ or larger swing lathe. Please see item description for more details.
Hurricane Turning Tools, Large Dovetail Jaws for HTC100 Woodturning 4 Jaw Wood Lathe Chuck
- This listing is for a set of large dovetail jaws, which are used on the hurricane htc100 4 jaw woodturning scroll chuck. Many jaw sets are available and inserts are interchangeable for use on today’s most popular lathes. They can be used in compression mode for gripping a tenon or expansion mode for internal holding within a dovetail recess. These jaws are only compatible with the htc100. Don’t have an htc100 if you haven’t heard of the hurricane htc100 4″ woodturning chuck, please check it out in our ebay store. It is a super high quality chuck, without the super high price of competitive chucks.
Hurricane Turning Tools, Standard Dovetail Jaws for HTC125 Woodturning 4 Jaw Wood Lathe Chuck
- These jaws are normally included in the basic chuck kit, but you might need an extra set, or purchased a chuck as “body only” these jaws are only compatible with the htc125. Standard dovetail jaws are the most common jaw type used in woodturning. They can also be used in expansion mode for holding inside a dovetail recess. They are typically used in compression mode for holding a tenon or “foot” on the bottom of a bowl or platter. This listing is for a set of standard dovetail jaws, which are used on the hurricane htc125 4 jaw woodturning scroll chuck. Measurements compression 2 1/4 “, 4 1/8″ expansion 2 7/8″, 4 3/4″.
Hurricane Turning Tools, Pin Jaws for HTC125 Woodturning 4 Jaw Wood Lathe Chuck
- These jaws are only compatible with the htc125. This gives you better access to the bottom of the bowl for easier tool work while your bowl is on the lathe. The dovetail is set away from the flat jaw surface by about 1 inch. The straight side can be used to hold the inside of a small box body. In compression mode, they can grip a small part like a final, or pen mandrel. This listing is for a set of pin jaws with dovetail , which are used on the hurricane htc125 4 jaw woodturning scroll chuck. These jaws are for small work and have several uses used in expansion mode for internal holding within a dovetail recess.
PSI CSC2000C Barracuda Wood Lathe Chuck System by PSI Woodworking
- Screw chuck insert for bowl turning. Chuck body threaded 1-1/2-inch by 8tpi, with optional adapters to 1-inch by 8tpi, 1-1/4-inch by 8tpi, m33 by 35 mm. Psi csc2000c barracuda wood lathe chuck system. Comes with 4 sets of jaws 1 step jaws, 2 round jaws, 3 wide jaws and pin jaws. Long shaft chuck key, “t” handled allen wrench.
Hurricane Turning Tools, Serrated Jaws for HTC125 Woodturning 4 Jaw Wood Lathe Chuck
- They can be used for this but they are not as strong as dovetail jaws. Serrated jaws are used for gripping end grain cylinders. They differ from dovetail jaws in that they are not tapered and have tiny gripping “serrations”. This listing is for a set of serrated jaws, which are used on the hurricane htc125 4 jaw woodturning scroll chuck. . Some turners use the serrated jaws instead of dovetail jaws in compression mode for gripping a tenon or expansion mode for internal holding within a recess.
PSI CSC2000C Barracuda Wood Lathe Chuck System by PSI Woodworking
- Please see item description for more details. For large bowl turning (requires 16″ or larger swing lathe. Also includes 8 extra long mounting screws for double jaws use (see description). Psi csc2000c barracuda wood lathe chuck system. Kit includes 6040 12″ cole jaws, 6039 12-15″ cole jaw adaptors, and 6030 buffer acc kit.
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
