13 Apr 2018
Top 22 Woodworking Products
PSI Woodworking Products LCJC8 8-1/2-Inch Bowl Finishing Chuck - Save the time (10-15 minutes) and the inconvenience of swapping and installing jumbo jaws on your lathe chuck every time you have to finish the bottom of a bowl. This dedicated chuck is a necessity for every bowl turner. Pre-threaded for a 1″ x 8tpi headstock. Introducing the breakthrough convenience of our new dedicated bowl finishing chuck. Will mount on other headstocks with the proper spindle thread adapters. The chuck features a key operated chuck body for quick and firm positioning, a chuck key, and 2 sets of grip pins. The chuck includes a set of pre-installed jaws large enough to make an 8-1/2″ bowl.
PSI Woodworking Products CF3J Faceplate 1-Inch by 8TPI 3-Inch Diameter, Model: CF3J, Tools & Hardware store - Fits any lathe with a 1-inch by 8tpi spindle thread. Has machined flats to grip with a wrench, easy on and easy off. 3-inch diameter faceplate with 4 screw mounting holes. Perfect for all small bowl turning. All steel construction.
PSI Woodworking Products CF3J Faceplate 1-Inch by 8TPI?3-Inch Diameter by PSI Woodworking - Rinsable and reusable. Two sanding grades on one sponge. Psi woodworking products cf3j faceplate 1-inch by 8tpi3-inch diameter. Rinsable and reuseable. Mineral on all four sides. Tough, aluminum oxide mineral bonded with flexible waterproof adhesive.
PSI Woodworking Products TM32 1/2-Inch Diameter Drill Chuck with a 2 MT Mount by PSI Woodworking - Will hold drill bits up to 1/2-inch in diameterdrill chuck mounts in the 2 mtcan be used in either the headstock or tailstocktightens with a chuck key for excellent gripremoved easily with a knock-out bar.
PSI Woodworking Products LBUFFSYS 3-Step Buffing System by PSI Woodworking - Set of three 8-inch fabric buffing wheelstripoli bar, white diamond bar, carnauba wax bar2 mt heavy duty lathe mandrel which holds the buffing wheelsthe system requires a lathe with a minimum of 1/2hpit is recommended that the final piece be pre-treated with danish oil.
PSI Woodworking Products PKMSTS2 2 MT Live Mandrel Saver, Model: PKMSTS2, Tools & Hardware store - There is no longer a need for spacer bushings. Unique design to support the end of your mandrel. Will work with all mandrels with a diameter of 0245-inch or less. Provides no pressure on the mandrel thus eliminating any bending and vibration. The live center is now obsolete.
PSI Woodworking Products CSCBARR4 Barracuda4 Powergrip Key Chuck - 4-1/2-inch diameter, 8 lb body-all components are packaged in a wood carrying case. Comes with 4 sets of jaws 1 step jaws, 2 round jaws, 3 wide jaws and pin jaws. Chuck body threaded 1-1/2-inch by 8tpi, with optional adapters to 1-inch by 8tpi, 1-1/4-inch by 8tpi, m33 by 35 mm. Long shaft chuck key, “t” handled allen wrench. Screw chuck insert for bowl turning.
PSI Woodworking Products LBUFFSYS 3-Step Buffing System - The system requires a lathe with a minimum of 1/2hp. Tripoli bar, white diamond bar, carnauba wax bar. Set of three 8-inch fabric buffing wheels. 2 mt heavy duty lathe mandrel which holds the buffing wheels. It is recommended that the final piece be pre-treated with danish oil.
PSI Woodworking Products LCDOWEL Dowel Collet Chuck System - 5 collets 1/4-inch, 3/8-inch, 1/2-inch, 5/8-inch and 3/4-inch. 1-inch by 8tpi thread with 3/4-inch by 16tpi spindle adapter, with collet closing head. Excellent gripping for small diameter dowels and tenons. Blow-molded carrying case. Perfect to hold a pen mandrel, and other small wood projects where a tenon is used.
PSI Woodworking Products LCMBEAD8 Finger Grip Bead Chisel - Add a little flare, style and functionality to your pens with this precision finger grip chisel. Overall length 17-1/2-inch, cut width 3/4-inch. The tool turns 8 perfectly spaced “finger grip” beads with a single cut. Ideal for pens or decorative finishes on a variety of projects.
PSI Woodworking Products TM32KL Keyless 1/2-Inch Drill Chuck with a 2 MT Mount - Tightens by hand without the need for a chuck key. Can be used in either the headstock or tailstock. Will hold drill bits up to 1/2-inch in diameter. Drill chuck mounts in the 2 mt. Removed easily with a knock-out bar.
PSI Woodworking Products TM32KL Keyless 1/2-Inch Drill Chuck with a 2 MT Mount, Model: TM32KL, Tools & Hardware store - Tightens by hand without the need for a chuck key. Will hold drill bits up to 1/2-inch in diameter. Removed easily with a knock-out bar. Drill chuck mounts in the 2 mt. Can be used in either the headstock or tailstock.
PSI Woodworking Products PKMSTS2 2 MT Live Mandrel Saver - Unique design to support the end of your mandrel. Provides no pressure on the mandrel thus eliminating any bending and vibration. Will work with all mandrels with a diameter of 0245-inch or less. There is no longer a need for spacer bushings. The live center is now obsolete.
PSI Woodworking Products LR220-3 220V Long Ranger Dust Collector Switch by PSI Woodworking - Turn on/off the dust collector anywhere in the shop220 volt, 2. 5 hp, 15 amp relay/receiverfcc approved25 amp internal circuit breaker included in the receiver5 foot power cord.
PSI Woodworking Products TM32KL Keyless 1/2-Inch Drill Chuck with a 2 MT Mount by PSI Woodworking - Psi woodworking products tm32kl keyless 1/2-inch drill chuck with a 2 mt mount. Uses single and double size rolls only, not jumbo or mega rolls. Recesses into wall or cabinet. Easy installation. Solid pine construction.
PSI Woodworking Products LCENTSET 7-Piece Multi Spur Drive Center Set With A 1-Inch by 8 TPI Mount by PSI Woodworking - Psi woodworking products tm32kl keyless 1/2-inch drill chuck with a 2 mt mount. Easy installation. Solid pine construction. Uses single and double size rolls only, not jumbo or mega rolls. Psi woodworking products lcentset 7-piece multi spur drive center set with a 1-inch by 8 tpi mount.
PSI Woodworking Products LCSIDE2 Round Side Scraper Chisels, 2-Piece set - The scrapers have a radius designed to easily shear the wood and create a clean smooth finish. Two piece hss inboard scraper set # lcside2. These heavy duty round end inboard side scrapers are equipped with thick, stable blades so you can cut aggressively without vibration. Smaller scraper is 16″ overall length with a blade 6″ long x 3/4″ wide and 5/16″ thick. Larger scraper is 19″ overall length with a blade 6″ long x 1″ wide and 3/8″ thick. These chisels are ideal for making final cuts inside bowls.
PSI Woodworking Products LABAR418 Lathe Spindle Adapter for a 1-Inch by 8TPI Spindle to 1-1/2-Inch by 8TPI Chuck - Necessary to convert a 1-1/2-inch by 8tpi female chuck thread to mount to a 1-inch by 8tpi spindle. No need to purchase a different chuck for that other lathe. Precision cut threads with a black and iodized finish. Adds versatility to your chuck. Allows you to use your chuck on different lathes.
PSI Woodworking Products LR220-3 220V Long Ranger Dust Collector Switch - • Turn your dust collector on/off from anywhere in the shop • 220 volt 2. Grounded with a reset button this remote uses fry signal which is not affected by outside interference by large tv-inchs transformers electrical noise or 3 phase power sources. Remote control transmitter and receiver 220 volt handles up to a 2. 5 hip 15 amp relay/receiver • feck approved • 25 amp internal circuit breaker included in the receiver • 5 foot power cord. 5 maximum hip motor 20 amp relay receiver. . Turn on a dust collector from anywhere in the shop with the remote dust collector switch.
PSI Woodworking Products TM32 1/2-Inch Diameter Drill Chuck with a 2 MT Mount - Drill chuck mounted in the #2 mt can be used in either the headstock or tailstock. Accepts a 1/4-20″ draw bolt (not supplied) for safety. Will hold drill bits up to 1/2-inch in diameter. Tightens with a chuck key(included) for excellent grip. A 1/2-inch diameter 3-jaw mechanism can be used for securing small turnings or pen mandrels at the headstock, or a drill bit in the tailstock. #2 morse taper mount for delta, jet, psi, and other midi lathe headstocks and tailstocks. Removed easily with a knock-out bar.
PSI Woodworking Products CSCPENCHK Dedicated Pen Drilling Lathe Chuck - Place this chuck containing your blank on your spindle. The chuck includes two dedicated 2″ jaws that will hold your blanks dead-center on the headstock. Drill a perfectly centered hole in your blank on your lathe using this unique lathe chuck. Mount a drill chuck with your drill bit into your tailstock and advance the drill into your blank as it spins on your lathe. The result is a perfect straight hole exactly where you want it.
PSI Woodworking Products LBUFFSYS 3-Step Buffing System by PSI Woodworking - Set of three 8-inch fabric buffing wheelstripoli bar, white diamond bar, carnauba wax bar2 mt heavy duty lathe mandrel which holds the buffing wheelsthe system requires a lathe with a minimum of 1/2hpit is recommended that the final piece be pre-treated with danish oil.
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.